What is the AUX button on Viper remote?

Press and release the “AUX” button to operate in “Silent Mode.” This stops the horn from sounding and the lights flashing to confirm activation of the alarm.

How do I know which Viper alarm I have?

The model number of your specific system is available on the cover of the owner’s manual, and can sometimes be found on the original sales receipt.

Why is my Viper alarm not working?

Once inside the vehicle locate your valet switch. If the procedure mentioned above does not work simply turn the key off then back on and press the valet switch two times. If this does not work turn the key off then back on and try it three times. Continue this up to five and one of them should disarm the alarm.

Can you reprogram a Viper remote?

To program your remote please do the following: Open the driver door. Press and hold the “F” button on the remote for 8 seconds or until the orange LED lights up solid at the top. Once the orange LED lights up solid, let go of the “F” button and press the remote start button until you hear 3 beeps from the remote.

How long does Viper remote start?

Any vehicle started with the remote engine starter can idle for a total of 20 minutes. Automatic engine shutdown occurs after 10 minutes, but the vehicle may be remotely started as many times as you wish for an additional 10 minutes.

How do you turn off Viper remote start?

How to Turn Off a Remote Car Starter

Press and hold the lock button on your remote while the car is running in auto-start mode.
Wait until the locks on the car repond by flashing. If they do not respond on the first press, press the button again every couple seconds until they respond.

How can I tell if my car has a remote starter?

Check your vehicle’s key fob The key fob for your car will have a special button if your vehicle has a remote starter. The symbol for the remote start is usually an arrow making a partial circle, as seen above. However, take note that some vehicle brands might use a different symbol for remote start.

Where is my Viper remote start?

A common location would be on the driver’s kick panel cover, or on the side of the center console (if the vehicle has one). Once this switch is located you will need to put your key into the ignition cylinder and turn it to the “ON” or “RUN” position.

How do you reset a Viper?

If you want to reset your Viper alarm, you can do so with your car’s fob key.

Point the fob key toward your vehicle as the alarm sounds.
Listen and wait for your alarm to sound for six seconds. Press the lock button on your key. Your vehicle’s Viper alarm will reset but the alarm will still be armed.

How do I get my viper out of valet mode?

This method has you open the driver door, then press the lock button, immediately followed by the unlock button, immediately followed by the lock button again. The LED will illuminate solid to indicate the vehicle is in valet mode. To exit this mode, simply repeat the process.

What kind of transmitter is the dei474v Viper?

DEI474V Viper Transmitter, Model 474V User Manual 473_474V Blister Packs.qxd DEI Headquarters, . DEI474V Viper Transmitter, Model 474V User Manual 473_474V Blister Packs.qxd DEI Headquarters, . DEI Headquarters, . Viper Transmitter, Model 474V

Which is the dei 474v Viper blister pack?

DEI474V Viper Transmitter, Model 474V User Manual 473_474V Blister Packs.qxd DEI Headquarters, . DEI Headquarters, . Viper Transmitter, Model 474V fREPLACEMENT TRANSMITTER Model 474V, 4 Button HF, Stealth Code Remote The following Learn Routine can be used to program this replacement transmitter to the system.

How to remove the valet key from a Viper transmitter?

While holding the Valet/program button, press the button from the transmitter you wish to assign to that channel. The unit will chirp to confirm that the transmitter has been taught to the receiver Release. Once the code is learned you can release the Valet/Program button and remove the key.

When do you need help with a Viper?